Calibration of laser beam direction for optical coordinate measuring system

For the purpose of measuring free form surfaces of some key parts in the aviation field accurately and effectively, such as blades, a non-contact optical coordinate measuring system is set up in the paper. A laser displacement sensor is mounted on the Z axis of a CMM via a turntable and adjusted to the suitable orientation according to the shape of the target surface. The combination of optical sensor and CMM can reach the full potential of them both. To enable the laser sensor to perform measurement in every direction, a calibration method used to determine the laser beam direction based on a standard sphere is proposed, the principle of which is analyzed in detail in the paper. In the calibration procedure, the sensor moves at an equal step along X, Y and Z axes respectively and then equation sets are established to calculate the unit direction vector of the line which the laser beam is on. In the process of solving the unknown quantities, a new parameter substitution method is applied. Finally, a gauging block and a sphere with known size are used to verify the method. As the experimental results show, the measuring errors in several directions are all smaller than 0.05 mm, which manifests that the calibration method proposed can meet the requirements of reverse engineering.     

A derivative UKF for tightly coupled INS/GPS integrated navigation

The tightly coupled INS/GPS integration introduces nonlinearity to the measurement equation of the Kalman filter due to the use of raw GPS pseudorange measurements. The extended Kalman filter (EKF) is a typical method to address the nonlinearity by linearizing the pseudorange measurements. However, the linearization may cause large modeling error or even degraded navigation solution. To solve this problem, this paper constructs a nonlinear measurement equation by including the second-order term in the Taylor series of the pseudorange measurements. Nevertheless, when using the unscented Kalman filter (UKF) to the INS/GPS integration for navigation estimation, it causes a great amount of redundant computation in the prediction process due to the linear feature of system state equation, especially for the case with system state vector in much higher dimension than measurement vector. To overcome this drawback in computational burden, this paper further develops a derivative UKF based on the constructed nonlinear measurement equation. The derivative UKF adopts the concise form of the original Kalman filter (KF) to the prediction process and employs the unscented transformation technique to the update process. Theoretical analysis and simulation results demonstrate that the derivative UKF can achieve higher accuracy with a much smaller computational cost in comparison with the traditional UKF.     

Reducing the complexity of distance measurement methods for circular turbo codes that use structured interleavers

The knowledge of turbo code's minimum Hamming distance (d_min) and its corresponding codeword multiplicity (A_min) is of a great importance because the error correction capability of a code is strongly tied to the values of d_min and A_min. Unfortunately, the computational complexity associated with the search for d_min and A_min can be very high, especially for a turbo code that has high d_min value. This paper introduces some useful properties of turbo codes that use structured interleavers together with circular encoding. These properties allow for a significant reduction of search space and thus reduce significantly the computational complexity associated with the determination of d_min and A_min values. © 2014 The Authors. International Journal of Communication Systems published by John Wiley & Sons, Ltd.     

Using microwave near-field reflection measurements as a non-destructive test to determine water penetration depth of concrete

A non-destructive version of a standard test for concrete permeability has been demonstrated. The method is based on water penetration depth estimation from near-field microwave measurements using an open-ended rectangular waveguide. In particular, water penetration is determined from the differential measurement of reflection coefficient in the S-band before and after injection of water under pressure. Experimental results show a good correlation between the standard destructive test and the new method. Microwave measurements simplify the standard test avoiding the need of drilling out a sample from the structure and thus reducing both the cost and time needed in the analysis.     

Performance curve available for non-steady flow through Venturi-like reverse flow diverter

A reverse flow diverter (RFD) consists of a driving nozzle, a diffuser, and a suction gap that separates the nozzle and diffuser. Thus, the RFD is a Venturi-like fluidic component with three ports. The jet flow emanating from the driving nozzle exit can entrain the ambient fluid and transport it to a high elevation. During this time, the flow through the RFD is non-steady, which makes it difficult to measure the flow depending on the pressure drop. In this study, a series of tests was carried out to evaluate this fluid flow with different contraction ratios, suction gap lengths, fluid properties, inlet flow rates, and inlet pressures. A performance curve was formulated that can be expressed as an exponential equation correlating the non-dimensional Euler number, pressure ratio, and suction factor. The performance curve is not affected by the driving nozzle exit diameter and suction length of the RFD. The performance curve makes it possible to measure the flow out of a RFD depending on the pressure drop.     

Assessing the width of Gaussian density of states in organic semiconductors

The Density of States (DOS) is an ingredient of critical importance for the accurate physical understanding of the optoelectronic properties of organic semiconductors. The disordered nature of this class of materials, though, renders the task of determining the DOS far from trivial. Its extraction from experimental measurements is often performed by driving the semiconductor out of thermal equilibrium and therefore requires making assumptions on the charge transport properties of the material under examination. This entanglement of DOS and charge transport models is unfavorable since transport mechanisms in organic semiconductors are themselves still subject of debate. To avoid this, we propose an alternative approach which is based on populating and probing the DOS by means of capacitive coupling in Metal Insulator Semiconductors (MIS) structures while keeping the semiconductor in thermal equilibrium. Assuming a Gaussian shape, we extract the DOS width by numerical fitting of experimental Capacitance–Voltage curves, exploiting the fact that the DOS width affects the spatial distribution of accumulated charge carriers which in turn concurs to define the MIS capacitance. The proposed approach is successfully tested on two benchmark semiconducting polymers, one of n-type and one of p-type and it is validated by verifying the robustness of the extraction procedure with respect to varying the insulator electrical permittivity. Finally, as an example of the usefulness and effectiveness of our approach, we study the static characteristics of thin film transistors based on the aforementioned polymers in the framework of the Extended Gaussian Disorder transport model. Thanks to the extracted DOS widths, the functional dependence of current on the gate voltage is nicely predicted and physical insight on transistor operation is achieved.     

田赛距离测量中全站仪的设计与实现

本文提出了将智能全站仪这种精密测量仪器广泛应用于田赛项目测量中，并结合其他科技元素用于解决田赛项目中跳远、投掷等项目的测量及数据管理问题，实现实时、自动、准确地裁定和报告比赛成绩。     

关于信息化测绘时代工程测量发展的思考

如今我国信息化技术全面发展，尤其对于工程测量工作领域来讲，不管是在工程建设和管理方面都产生不小的支撑引导效用。由此，笔者具体结合如今工程建设信息化测绘核心任何以及设备布置细节，进行结构整体安全管理周期和周边地理空间信息技术发展能效整理解析，试图将工程测量最新发展机遇和技术挑战问题处理完全。希望能够借此为日后一定时期范围内相关工程测量规划主体提供合理指导性建议内容，最终为我国各类工程事业可持续发展前景绽放奠定深刻适应基础。     

Investigation of the residual stress in UO2-Mo composites via a neutron diffraction method

UO₂-Mo composites with a core-shell structure have been considered candidates for the thermal conductivity (TC)-enhanced UO₂ pellets and have demonstrated commercial potential for use in novel high-level safety reactors. Nevertheless, UO₂-Mo composites tend to form micro-cracks that are caused by the presence of residual stress (RS) during manufacturing. In this work, neutron diffraction measurements were employed to analyse the RS in UO₂-Mo core-shell structured composites fabricated by spark plasma sintering (SPS) for the first time. It was found that in the UO₂-Mo composites, the RS state present in the UO₂ matrix was tensile in nature. The RS in the UO₂ matrix increased with increaseing Mo content. There was a maximum value of 148 ± 15 MPa in the UO₂-10 vol% Mo composite. The micro-cracks produced in the high-Mo content composites were explained by the results of the neutron diffraction measurements. These results could provide significant guidance for the manufacturing and improvement of the operational performance of UO₂-Mo composites as next-generation fuels.